|
Post by mackintoshman on Aug 21, 2023 9:15:37 GMT -8
Does anyone have a manual to rebuild the 50 fathom. Thanx, Mac.
|
|
|
Post by hgslick on Aug 21, 2023 10:04:22 GMT -8
I just used the Voit manual off of Vintage Double Hose. I restored one recently using that resource. I have also found an excellent color match heat cured paint if you need to refinish.
|
|
|
Post by mackintoshman on Aug 21, 2023 10:19:30 GMT -8
I went to VDH but couldn't download the file. And yes I do need to repaint.
|
|
|
Post by james1979 on Aug 21, 2023 11:16:22 GMT -8
The VDH repository is gone. I did download the entirety a little while back, and I'm putting it in my google drive now (a couple hours left on the upload). I'll try to sort out sharing it once it's uploaded. In the meantime, I messaged you my email... if you shoot me an email I'll reply back with the voit manual attached.
respectfully,
James
|
|
|
Post by broxton coalition on Aug 21, 2023 13:17:22 GMT -8
James, that is incredibly kind of you to help people source that info !! Thank you for your help. i know the library on VDH was very extensive, thanks to a number of dedicated vintage diver enthusiasts!
|
|
|
Post by vance on Aug 21, 2023 13:26:18 GMT -8
Several of us here saw the writing on the wall and downloaded all of the VDH files, so they are still available from one of us!
|
|
|
Post by snark3 on Aug 21, 2023 14:40:02 GMT -8
I just went on the VDH website. The files are still available. If you haven't downloaded them it might be a good idea to do it PDQ
|
|
|
Post by SeaRat on Aug 21, 2023 15:16:09 GMT -8
You might want to check out this thread too: vintagescuba.proboards.com/thread/4631/voit-50-fathom-regulatorWe have discussed this regulator here quite a bit. John PS, I just read through the above thread, and it talks more about bullets and how far they penetrate into water than the Voit 50 Fathom Regulator. So, if you want a good diversion, read this thread. Otherwise, go to the documents about the Voit 50 Fathom. PS2, Here is another thread about the 50 Fathom, and on the third page we talk about orienting the large hold down the intake, instead of the factory small hole down the intake. I used that configuration on mine for several years in the 1970s and 1980s, and it became my favorite regulator at that time. vintagescuba.proboards.com/thread/3573/won-50-fathom-on-ebay?page=3PS3, Here’s another thread where we talk about the Voit 50 Fathom: vintagescuba.proboards.com/thread/754/voit-50-fathom-timelinePS4, we have quite a lot of information about the Voit 50 Fathom regulator. This one discusses it as the only downstream single stage regulator produced. vintagescuba.proboards.com/thread/293/stream-single-stage-regulator
|
|
|
Post by vance on Aug 21, 2023 15:59:34 GMT -8
I just went on the VDH website. The files are still available. If you haven't downloaded them it might be a good idea to do it PDQ As I recall, it isn't super easy to find them on Bryan's host site.
|
|
|
Post by nikeajax on Aug 21, 2023 16:03:12 GMT -8
So, which valve body does this use? Is it he same as the Mistral, or the VCR-5? JB
|
|
|
Post by hgslick on Aug 21, 2023 16:31:17 GMT -8
I believe the one he has is wearing a Mistral valve referring to the OP
|
|
|
Post by SeaRat on Aug 21, 2023 17:21:07 GMT -8
So, which valve body does this use? Is it he same as the Mistral, or the VCR-5? JB This is the Voit 50 Fathom valve body, inside a blue 50 Fathom set of boxes. This is a downstream valve, with the main lever on the side, and not hooked up. John
|
|
|
Post by hgslick on Aug 21, 2023 17:29:44 GMT -8
I did this one recently, too bad I didn't have any Tinns
|
|
|
Post by mackintoshman on Aug 21, 2023 19:52:31 GMT -8
Thank you ALL so much. I Have a lot of reading to do...
|
|
|
Post by duramax on Aug 22, 2023 6:10:27 GMT -8
FYI
Went to the VDH website and found that the directory structure is there but the downloads are zero bytes. This resource appears to be gone.
|
|