|
Post by duckbill on Sept 17, 2006 21:45:35 GMT -8
Is there a special tool designed specifically for Tinnerman hose clamps? I can see how they can come apart and be put back on, but it looks like a special tool to engage the notches would be helpful.
|
|
|
Post by crimediver on Sept 18, 2006 4:18:02 GMT -8
I have also wondered about that. I'm sure there is someone who knows but I sure don't. A tool would sure make it easier to replace.
|
|
|
Post by duckbill on Sept 20, 2006 10:08:34 GMT -8
I've searched the internet for Tinnerman pliers, and so far nobody here has described the correct tool. I would imaging the correct tool is a type of pliers made for the job. Well, the seal on my Buick's water pump just gave out (Oh, joy! ), so while I was at the auto parts store I checked out all of their tools in case they might have something that would work on the Tinnermans. I found a tool that works. I had to modify it slightly with a file, but it does the job. The only down side is that the tips could be wider. Oh, well. Here is an "after" photo of the tool points. I didn't get a "before" photo, sorry to say. But, if someone gets the tool they will see what needs to be done. It is called a "C-V Joint Boot Clamp Plier". I'm still looking for a proper tool, though, if anyone can help.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Sept 20, 2006 10:28:06 GMT -8
Terry
I just use a screwdriver to disengage and a pair of needlenose pliers to engage the teeth....I have two dacors and a DARAM that had dacor hoses with the tinnerman clamps......it's sorta an art after you get the hang of engaging and disengaging.....but easy to learn..........
|
|
|
Post by JES on Sept 20, 2006 18:32:29 GMT -8
Survivair (a manufacturer of SCBAs) mentions the following tool to tighten Tinnerman clamps:
|
|
|
Post by duckbill on Sept 20, 2006 21:21:37 GMT -8
Yea, I tried the needlenose pliers, but I was afraid that the points would slip off and mar the finish due to the angle. Hence, the tool quest. Small screwdriver works fine for taking them off, though. I didn't check Sears, but thanks for that information, Joe. I'll go see what that tool looks like.
|
|
|
Post by admin on Nov 16, 2006 14:27:12 GMT -8
Terry; Your custom made Tinnerman pliers are a stroke of genius! I've been looking for original Tinnerman clamp pliers for years and I've heard reference to them but I've never seen a pair. I'm attaching an ad from a June 1945 issue of Popular Mechanics. It shows the "new' Tinnerman clamps that were mostly used in military aircraft. But surprisingly, the pliers they show in the ad are just a pair of standard pliers. Dan
|
|
|
Post by duckbill on Nov 16, 2006 16:28:41 GMT -8
Thankyou, Dan. The clamp in your picture is the same style which is on the 1 1/2 inch hose ends of the nice Dacor R-4 which Robert ('scubadiverbob') gave me (He is a very nice and generous person. I am indebted to him for that one!). I tried pliers before like your ad shows, but I knew these clamps are a little hard to find, and one slip and, well.....one scratched Tinnerman. The 1-inch end Tinnermans are a different design and were really the ones that had me stumped for a solution. The tool I made works O.K., but I wish the plier blades were wider where they contact the clamp. Thankyou for sharing that. I love how the old ads were so instructional.
By the way, 'JES' Joe, thanks again for the information on the Sears tool 9HT52136, but it turned out to be a dead end. The guy at Sears here couldn't find a tool under that number. It may be that he just didn't know what he was doing though.
|
|